DJI Phantom 3 Pro crash flight log,battery problem >?

[Daniel_R]

Hi there,

I have crashed my P3Pro and it seems battery failed see attached log, but I have heard some people get lower voltage then mine 11V and aircraft still was ok anyway I broke gimbal arm and wire tape, ordered repaired. Now Drone is connecting to the remote control fine I can see live picture from camera and gimbal works as before but get lound beeping sound just after switching on the aircraft same as this guy here https://www.youtube.com/watch?v=p37-fF3Y-Kg . I have followed steps he showed without success, after few minutes my light go solid red on the gimbal.

What I noticed my battery seems ok I can charge it and light bars works fine but there is no data when checking on DJI GO App it shows 0% on all cells 0V all options seems disable.
Rest looks fine I can format SD GPS ok etc via DJI GO App

From SD Card hidden file “P3X_FW_LOG_AB” I have noticed few modules not deceted as showed below, but for some people in similar case reinstal firmware helped:

[00012604]========== remo-con disconnect. boot(15) ============
[00012681]Packet [C:\P3X_FW_V01.11.0020.bin] detected, card sn [0xe4dd0630].
[00012753]Packet upgrade start…

[00012836]Packet checking…
[00012908]Packet vlink 01.11.0020 ↔ 01.11.0020.
[00012985]Record vlink 01.11.0020 ↔ 01.11.0020 (flow = 0).
[00013059]Done.

[00013127]Version checking[1]…
[00025701][03 06][00] device not detected.
[00038271][03 05][00] device not detected.
[00038478][04 00][00] v1.48.0.0 → v1.48.0.0
[00051052][11 00][00] device not detected.
[00063621][11 01][00] device not detected.
[00076200][12 00][00] device not detected.
[00088774][12 01][00] device not detected.
[00101348][12 02][00] device not detected.
[00113930][12 03][00] device not detected.
[00114095][15 00][00] v1.1.2.0 → v1.1.2.0
[00126661][17 00][00] device not detected.
[00139231][17 01][00] device not detected.
[00139325][19 00][00] v1.0.8.96 → v1.0.8.96
[00139395][01 00][00] v1.32.5432 → v1.32.5432
[00139471][01 01][00] v1.32.5432 → v1.32.5432
[00139561][08 00][00] v0.13.0.7 → v0.13.0.7
[00139665][09 00][00] v4.1.0.0 → v4.1.0.0
[00139735]Packet upgrade failed at version checking.

Do you thing that can be just battery problem and that is why I get very lound beeping, and can not get it working?

Can not paste files here as I am newbi but link below
drive.google.com/drive/folders/1E0Zr1GZpWl-qveOquo89MAL_DuxT86is?usp=sharing

Thx in advance

[Fly_Dawg]

@Daniel_R

I have crashed my P3Pro and it seems battery failed see attached log, but I have heard some people get lower voltage then mine 11V and aircraft still was ok

Your P3 did not simply crash. There is nothing wrong in the flight log. You simply ran out of battery power. Max flight time for a P3 is ~23 min. The aircraft went in to autoland when the battery was too low and it reached the shut off point during the process.

You can see the full flight data here: https://www.phantomhelp.com/LogViewer/CIQE9CYZ8UK381IQTR7I/

[Daniel_R]

Thanks for reply!

Does it mean my battery should be ok?

As described above now fully charged battery shows 0V on all cells and 0% when I check it on DJI GO App battery section.

Still lound beeping and can not reinstall firmware, I thought maybe because of battery as showing 0% in App

THX in advance!